As the leaves come down it’s easier to see into the forest canopy, and the summer nests of squirrels become more visible. The photo below shows a gray squirrel nest, a leafy structure located on a supporting branch junction. Also known as dreys, gray squirrel nests are usually located in crotches or branch junctions of deciduous trees. To build a nest in a tree, a squirrel constructs a framework of twigs and stuffs it with leaves, then makes an entrance hole and hollows out the inside of the structure. A lining of soft material such as moss or dry grass is added, and a second opening is made to serve as an emergency exit. Dreys differ from bird nests in being roughly spherical, with an enclosed interior space connected to the outside through small openings. Bird nests also lack the leafy appearance of gray squirrel nests.
Red squirrel nests are similar but are likely to incorporate a variety of materials in the outer layers. They are also more likely to be built in conifers. The next photo shows a red squirrel nest located in a larch tree. Twigs and grasses form the lower part of the nest, and fragments of plastic sheeting cover the upper part.
The nest shown above was easy to see in winter when the larch was leafless, but nests located in evergreen conifers are harder to find. The one in the photo below was tucked up against the trunk of a Norway spruce tree.
Here’s another red squirrel nest which was constructed in the crotch of a Scots pine.
There’s not nearly as much information available on flying squirrel nests, no doubt because flying squirrels are nocturnal and not as easily observed as gray and red squirrels. Mark Elbroch, in Mammal Tracks and Sign, Second Edition, reports that flying squirrel dreys are smaller than red or gray squirrel nests and are made of grasses and other fine materials rather than leaves.
In more southern climes dreys may suffice for winter lodging, but in our area squirrels move into more sheltered accommodations when the weather gets cold. Human structures are used where they are available, but hollow trees are the preferred choice for forest-dwelling squirrels. Nests enclosed in protective walls of wood and lined with insulating materials provide warmth, protection from the weather, and security. But is there any way for us to know which tree houses a nest? It’s not always possible, but there may be clues. The tree in the photo below must have had a good nesting space because it had been marked with a few bites. We recognize the bites visually, but the persistent odor of the resident squirrel’s saliva is more important to other squirrels, signaling that the space is occupied.
Red, gray, and flying squirrels all make winter nests in hollow trees. If the opening is quite small it’s probably not occupied by a gray squirrel, but beyond that, the size of the opening doesn’t tell us much about who the occupant is. I’ve found marked openings in trees where gray squirrels are absent and red squirrels are common, and also in areas where the reverse is true, so I believe that both species create bite marks to claim nest sites.
Bite marks can be sparse, like the ones above, or plentiful, like the artistic creation in the next image. I suspect that the double ring of bites was created because the owner felt threatened by the presence of other squirrels.
Nests in hollow trees continue to be useful well into spring as birthing dens. But although well protected from the elements, they have a drawback: there is usually just one entrance. In the next photo you see some nest lining that was removed from a nest and ended up in a pile on the ground. This would only have happened if a predator had raided the nest and, in the process, pulled the nest lining out. It could have been a fisher, or possibly a raccoon. Both are good climbers and fishers are considered to be specialists in squirrel predation. At any rate, nests in hollow trees are not completely safe.
In addition to clues about predation, the photo above shows us what nest lining looks like. To make this material, squirrels harvest bark and process it into finely divided strands that can be stuffed into tree cavities to provide insulation. The bark usually comes from dead branches, but may also be gathered from living stems of plants such as honeysuckle or white cedar.
The next image shows a dead striped maple branch that was stripped for nest lining. The exposed wood and fibrous remnants may bring to mind a buck rub, but buck rubs differ in several ways. Buck rubs are made on living stems that are more or less upright and have no obstructions that would hinder the approach of a large animal. Rubs are usually limited to one continuous section of the stem and occur at heights between 1 1/2 and 4 feet off the ground. Branches stripped by squirrels have random angles from vertical and could be anywhere from ground level (including fallen branches lying on the ground) to much higher. Bark is usually removed from multiple areas, and there may be a tangle of branches that would make it hard for a deer to reach the debarked sections. And finally, the wood surface of a buck rub shows signs of abrasion, while the wood exposed by squirrel stripping is mostly smooth.
Stripped branches do sometimes have telltale squirrel tooth marks like the ones in the photo below.
If you keep track of weather you’ll notice that cold nights are often followed by new bark stripping. I sometimes imagine a shivering squirrel thinking, “Wow, it was cold last night, I’m going to get more insulation for my nest!” Well, maybe it doesn’t happen exactly like that–sorry about the anthropomorphizing. But it’s clear that squirrels respond to cold with increased harvesting of fibrous bark. And it’s okay to imagine a squirrel sleeping in a cozy, insulated nest in a hollow tree on a cold winter night.