Looking On The Bright Side

The leaves are down, and the colorful spectacle of autumn is behind us. The forest has gone from a kaleidoscope of color to a narrow spectrum of browns and grays. But wait, what’s that pale streak glinting among the tree trunks? If you look closely you can see it in the center of the featured photo. Moving closer we can see that it’s a buck rub, bright wood laid bare by a hormone-driven male deer. This is rutting season for whitetail deer, and the bucks are roaming the landscape seeking receptive does. They leave their calling cards on living trees–anything from very young saplings to substantial trunks 8 inches or more in diameter. To make a rub the animal lowers its head and rakes its antlers up and down against the stem. Rough areas around the bases of the antlers work like files to abrade the outer bark down to the light colored sapwood.

The photo below is a close-up of the rub in the first photo. Rubs are usually between one and four feet above the ground, and their edges are often rough or stringy. Gouges made by the short tines near the antler bases are often present–look for them just above the debarked area. The brightness of the freshly exposed wood is what attracts our attention, and it may do the same for deer. But buck rubs also carry scent messages, deposited when the animal rubs its forehead against the newly bared surface. We’re not equipped to detect these chemical signals, but to a visiting doe they convey a wealth of information about the age, health, and even individual identity of the rub maker.

The light colored areas in the photo below have also been denuded of bark, but this wood was exposed by feeding rather than by rubbing. A porcupine climbed these yellow birch trees and chewed through the outer bark to get at the cambium, the living cells that produce both bark and wood during the growing season. There’s no mistaking this example for a buck rub, but porcupine chews are sometimes found close enough to the ground to be confusing. In both cases the light wood stands out against the bark, but there are several clues that distinguish rubs from chews.

Instead of a smooth surface, wood that has been exposed by porcupine feeding is textured by tooth grooves, and the margins are more irregular, as in the photo below. The tooth marks are just deep enough to reach the nutritious tissue, and are organized with a neatness that speaks of feeding efficiency. Along the margins of chews there are often tooth marks instead of the stringy fibers that mark the edges of rubs.

Beavers, like porcupines, rely on the cambium of woody plants for much of their winter diet. Being larger than porcupines, beavers’ wider incisors give their chews a more robust appearance. And rather than climb to access food, beavers bring the food down to their level by felling trees. The beaver that felled the log in the photo below stood on its back feet to feed, anchoring its upper incisors in the bark and drawing its lower incisors upward to scrape up the cambium. It moved systematically along the log, leaving the row of shallow upper incisor digs in the bark and the longer lower incisor marks below them. Like the porcupine, the beaver penetrated just deep enough to scrape up the nutritious cambium.

Not all bark chewers show this kind of efficiency. The sumac stem below was chewed by a rabbit, and its ragged appearance contrasts with the more orderly work done by beavers and porcupines. Rabbits only feed on small stems, and their chews show varying depths of penetration with projecting splinters of bark and wood. Like beavers they are limited to what they can reach from the surface they’re standing on, but if there’s a deep snow pack or heavy snow that bends branches down, rabbit chews can be found in some surprising places.

Here’s another kind of feeding that might catch your eye in the autumn woods. Woodpeckers worked on this standing dead tree to get at the insects in the outer layers of wood. The beak strikes left pits, partially lifted slivers, and gouges (best seen on the right edge of the tree). This kind of woodpecker work can be located at any height, and may even be found on downed logs, but unlike the previous examples, it only occurs on dead trees.

Here’s a final example of eye-catching brightness. As the weather gets colder, squirrels leave their leafy tree-top dreys and make nests in hollow trees or other protected places. They gather fibrous bark for nest lining, and in the process, leave freshly debarked wood for us to find. The dead, fallen branch in the photo below was stripped of its fibrous inner bark by a squirrel. Although there’s a vague resemblance to a buck rub, the position of the branch and its non-living status indicate squirrel work rather than deer.

When squirrels harvest fiber from woody plants they may leave another clue. In the photo below you can see the paired marks of a squirrel’s incisors. Much of the bark removal is done by pulling up long strips, but occasionally the squirrel leaves a bite mark as it grasps the bark with its teeth.

Squirrel stripping is also found on living stems–I’ve seen it on honeysuckle and red cedar–and these are more likely to be mistaken for buck rubs. But areas shredded by squirrels are often in places a deer wouldn’t be able to reach, higher on a trunk, within multi-stemmed shrubs, or on stems guarded by projecting branches. Deer prefer sites with straight stems and unobstructed approaches, and any small branches or twigs are usually broken off by the vigorous action of making a rub.

I love this time of year–the leaves are down, and I can see for greater distances through the trees. Many signs of animal activity are hidden by fallen leaves, but others have become more visible. And every once in a while a bright patch shining among the duller tones draws me in and opens up a new and interesting discovery.